Vous êtes ici : Version française > Publications scientifiques > Axe 2

Publications scientifiques Axe 2 Knowledge Based Design

Co-Auteurs Titre article Revue Impact Factor Année Références
(Volume) page début - page fin
ou DOI		 Projet LABEX
M. MARIÑO,
P. BREUIL,
M. RIEU,
D. JAMON, 
J.-M. RAMPNOUX,
J.-P. VIRICELLE,
F. GARRELIE		 Simulation of nanosecond IR laser annealing of cerium gadolinium oxide Journal of European Ceramic Society  3,4 2018 (38) 3875-3880  LASERDENS
A. RAMI,
F. GHARBI,
S. SGHAIER,
H. HAMDI		 Some Insights on Combined Turning-Burnishing (CoTuB) Process on Workpiece Surface Integrity International Journal of Precision Engineering and Manufacturing 1,497 2018 19(1) 67-78 Non financé par LabEx
S. LAFON PLACETTE,
J. FONTAINE,
M.-I. DE BARROS BOUCHET,
C. HEAU		 Critical role of a metallic counterpart on the tribochemical wear of ta-C coatings in base oil Wear 2,531 2018 (402–403) 91-99 USDLC
A. CHOLERIDIS,
S. SAO-JOAO,
J. BEN-MOHAMED,
D. CHERN,
V. BARNIER,
G. KERMOUCHE,
C. HÉAU,
M.-A. LEROY,
J. FONTAINE,
S. DESCARTES,
C. DONNET,
H. KLÖCKER		 Experimental study of wear-induced delamination for DLC coated automotive Surface and Coatings Technology 2,139 2018 (352) 549-560 MECA-INTER-DLC
A. RAMI,
A. KALLEL,
S. SGHAIER,
S. YOUSSEF,
H. HAMDI		 Residual stresses computation induced by turning of AISI 4140 steel using 3D simulation based on a mixed approach The international Journal of Advanced Manufacturing Technology 2,209 2017 (91) 3833-3850 ReGal
P. BARAL,
G. GUILLONNEAU,
G. KERMOUCHE,
J.-M. BERGHEAU,
J.-L. LOUBET		 Theoretical and experimental analysis of indentation relaxation test Journal of Materials Research 1,673 2017 32(12) 2286-2296 INDENTER
P. BARAL,
G. GUILLONNEAU,
G. KERMOUCHE,
J.-M. BERGHEAU,
J.-L. LOUBET		 Theoretical and experimental analysis of indentation, relaxation test Journal Of Material Research 1,673 2017 (7) 1-11 INDENTER
D.-Y. TUMBAJOY,
S. DESCARTES,
J.-M. BERGHEAU,
H. BAIDA,
C. LANGLADE,
G KERMOUCHE		 Investigation of graded strengthened hyper-deformed surfaces by impact treatment: micro-percussion testing Materials Science and Engineering, IOP Conference Series - 2017 194:012024 ICSEC
A. VIAT,
G. GUILLONNEAU,
S. FOUVRY,
G. KERMOUCHE,
S. SAOJOAO,
J. WEHRS,
J. MICHLER,
J.F. HENNE		 Brittle to ductile transition of tribomaterial in relation to wear response at high temperatures Wear 2,531 2017 (392-393) 60-68 ICSEC
A. BEN KAABAR,
A. AOUFI,
S. DESCARTES,
C. DESRAYAUD		 3D modeling of unconstrained HPT process: role of strain gradient on high deformed microstructure formation Materials Science and Engineering, IOP Conference Series - 2017 (194) 012044 CRIMET
D. TUMBAJOY-SPINEL,
S. DESCARTES,
J.-M. BERGHEAU,
V. LACAILLE,
G. GUILLONNEAU,
J. MICHLER,
G. KERMOUCHE		 Assessment of mechanical properties gradient after impact-based surface mechanical treatment. Application to a pure alpha-iron Materials Science & Engineering A 2,647 2016 (667) 189-198 ICSEC
M. MARIÑO,
M. RIEU,
J-P. VIRICELLE,
F. GARRELIE		 Laser induced densification of cerium gadolinium oxide: application to single-chamber solid oxide fuel cells Applied Surface Science  3,15 2016 (374) 370-374 LASERDENS
M. RIEU,
M. CAMARA,
G. TOURNIER,
J.-P. VIRICELLE,
C. PIJOLAT,
N.F. DE ROOIJ,
D. BRIAND		 Fully inkjet printed SnO2 gas sensor on plastic substrate Sensors & Actuators: B. Chemical 4,758 2016 (236) 1091-1097 Mobilité Suisse
M. Rieu
P. JURAN,
P.J. LIOTIER,
C. MAURICE,
F. VALIORGUE,
G. KERMOUCHE		 Investigation of indentation, impact and scratch-induced Mechanically Affected Zone of a copper single crystal C.R. Mecanique 0,988 2015 (343) 344-353 ICSEC
D. TUMBAJOY-SPINEL,
G. KERMOUCHE,
S. DESCARTES,
J.-M. BERGHEAU,
V. LACAILLE,
G. GUILLONNEAU,
J. MICHLER		 Identification des propriétés mécaniques des surfaces tribologiquement transformées (TTS) à partir d’essaiss de nano-indentation et micro-compression de piliers Matériaux & Techniques - 2015 (103) 303-311 ICSEC
M GUEDICHE,
T. MABROUKI,
C. DONNET,
J.-M. BERGHEAU,
H. HAMDI		 A new procedure to increase the orthogonal cutting machining time simulated CIRP Procedia - 2015 (31) 299-303 MOSUOC
M. RIEU,
M. CAMARA,
G. TOURNIER,
J.-P. VIRICELLE,
C. PIJOLAT,
N.F. DE ROOIJ,
D. BRIAND		 Inkjet Printed SnO2 Gas Sensor on Plastic Substrates Procedia Engineering  - 2015 (120) 75-78 Mobilité Suisse
M. Rieu
V. LACAILLE,
G. KERMOUCHE,
D.-Y. TUMBAJOY,
E. FEULVARCH,
C. MOREL,
J.-M. BERGHEAU		 Modeling nitriding enhancement resulting from the NanoPeening treatment of a Pure Iron Materials Science and Engineering
IOP Conference Series		 2,647 2014 (63) 012124-1 to 8 ICSEC
G. JACQUET,
G. KERMOUCHE,
C. COURBON,
D. TUMBAJOY,
J. RECH		 Effect of sliding velocity on microstructural evolution induced in copper Materials Science and Engineering
IOP Conference Series		 2,647 2014 (63) 012039-1 to 11 MOFOCOMM
ICSEC
C. HÉAU,
C. OULD,
P. MAURIN-PERRIER		 Tribological behaviour analysis of hydrogenated and non hydrogenated DLC lubricated by oils with and without additives Lubrication Science  1,384 2013 (25) 275–285 DLCTRIB